High Response Muffler Ver.S


  • A high-quality sports muffler developed by TRD in partnership with standard muffler manufacturers
    An all stainless steel exhaust system focused on performance and cost
    Even more reliable than genuine Toyota parts


    For SXE10, GXE10 ALTEZZA

    For #NH1#W ALPHARD

    For NCP91 Vitz RS

    For ZNE10G, ANE10G WISH

    For GSR50W, ACR50W ESTIMA

    For NCP6# ist

    For SCP10 Vitz

    For QNC2# bB

    For GRJ 150W, 151W, TRJ150W LAND CRUISER PRADO
    High Response Muffler Ver.S Series
    Vehicle Model Code Engine Model Year Model Part No. Code List Price(JPY) Remarks
    ALPHARD 240G/X
    Excluding Hybrid or
    Side Lift Up Seat Model
    2AZ-FE 08,05 - MS153-58003 E Discontinued φ75 Single tail
    240S
    Excluding Hybrid or
    Side Lift Up Seat Model
    2AZ-FE MS153-58004 E 66, 000 φ100 Single tail
    350G/X
    Excluding Hybrid or
    Side Lift Up Seat Model
    2GR-FE MS153-58005 E 66, 000 φ75 Single tail
    350S
    Excluding Hybrid or
    Side Lift Up Seat Model
    2GR-FE MS153-58006 E 66, 000 φ100 Single tail
    #NH1#W 1MZ-FE, 2AZ-FE 02.5- MS153-58001
    (17400-MH110)
    W Discontinued Applicable to MS・AS grade and vehicle with OE optional rear aero bumper.
    Pipe dia. φ48.6、φ100 Single tail(Cut-end curling finish)
    Tail end cut angle 15° *1
    MS153-58002
    (17400-MH100)
    W Discontinued Applicable to all models except above.
    Pipe dia. φ48.6、φ100 Single tail(Cut-end curling finish)
    Tail end cut angle 15° *1
    ALPHARD HYBRID ATH10W 2AZ-FXE 03.7- 17400-MH100 W 59, 000 Pipe dia. φ48.6、φ100 Single tail(Cut-end curling finish)
    Tail end cut angle 15° *1
    ALTEZZA SXE10 3S-GE 98.10- 17400-SE100 C Discontinued Pipe dia. φ65、φ115 Single tail
    Tail end cut angle 15°Slanting cut *2
    GXE10 1G-FE 98.10- 17400-SE100 C Discontinued Pipe dia. φ65、φ115 Single tail
    Tail end cut angle 15°Slanting cut *2
    AQUA NHP10 1NZ-FXE 11.12 -12.8 MS153-52010 E Discontinued Applicable to vehicle manufactured before 2012.08.27
    (Frame number to NHP10-2098374 and to NHP10-6075115)
    Certified to meet Japan noise regulations for public road use.
    φ70mm Dual tail (Cut-end curling finish)
    TRD logo attached on baffle.
    *Not compatible with under-mentioned "MS153-52011"
    * Recommend to install with TRD Rear Bumper Spoiler.
    *Do not install with Toyota Genuine accessory Rear bumper spoiler.
    1NZ-FXE 12. 8- MS153-52011 E 61, 500 Applicable to vehicle manufactured after 2012.08.27
    (Frame number from NHP10-2098375 and from NHP10-6075116)
    Certified to meet Japan noise regulations for public road use.
    φ70mm Dual tail (Cut-end curling finish)
    TRD logo attached on baffle.
    *Not compatible with above-mentioned "MS153-52010"
    * Recommend installation with TRD Rear Bumper Spoiler.
    *Do not install with Toyota Genuine accessory Rear bumper spoiler.
    ARISTO JZS160・161 2JZ-GE
    2JZ-GTE
    97.8- 17400-JS601 C Discontinued Pipe dia. φ60.5、φ115 Single tail comes on RH&LH
    Tail end cut angle 15°Slanting cut *2 *3
    AURIS ZRE152H 2ZR-FE
    2ZR-FAE
    06.10- MS153-12009 E Discontinued Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    TRD logo attached on baffle
    MS153-12002
    (17400-ZE500)
    E Discontinued
    NZE151H 1NZ-FE 06.10- MS153-12010 E Discontinued
    MS153-12003
    (17400-ZE510)
    E Discontinued
    bB NCP30・31 #NZ-FE 03.4- 17400-NP310 C Discontinued Pipe dia. φ42.7、φ89.1 Single tail(Cut-end curling finish),
    TRD logo attached on baffle *1
    BLADE *4 AZE156H 2AZ-FE 06.12- MS153-12013 E Discontinued Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    TRD logo attached on baffle
    MS153-12001 E Discontinued Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    TRD logo attached on baffle
    CARINA AT211 7A-FE 96.8-01.12 17400-ST100 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    CELICA ST202
    (Except 4WS model)
    3S-GE 93.10-97.12 *5 17400-ST000 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    3S-FE 93.10-99.9 17400-ST010 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    ZZT230 1ZZ-FE 99.9- 17400-ZT310 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut *6
    ZZT231 2ZZ-GE 99.9- 17400-ZT301 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut *7
    CELSIOR UCF3# 3UZ-FE -03.8 17400-UF300 C Discontinued Pipe dia. φ48.6 Oval shape Single tail(Cut-end curling finish)
    comes on RH&LH(Height60mm×Width100mm) TRD logo attached on baffle
    Tail end cut angle 40°
    UCF3# 3UZ-FE 03.8- 17400-UF310 C Discontinued Pipe dia. φ48.6 φ54 Dual tail(Cut-end curling finish) comes on RH&LH
    TRD logo attached on baffle
    Tail end cut angle 25°
    COROLLA FIELDER NZE121G 1NZ-FE 00.8-02.9 17400-NE200 W Discontinued Pipe dia. φ50.8、φ78 Dual tail(Cut-end curling finish) *1 *8
    ZZE122G 1ZZ-FE 00.8- 17400-ZE200 W Discontinued Pipe dia. φ50.8、φ78 Dual tail(Cut-end curling finish) *1 *8
    ZZE123G 2ZZ-GE 00.8-04.4 17400-ZE211 W Discontinued Pipe dia. φ60.5、φ78 Dual tail(Cut-end curling finish) *1 *8
    04.4- 17400-ZE230 W Discontinued Pipe dia. φ60 W100×H60 Oval shape single tail(Cut-end curling finish)
    TRD logo attached on baffle
    Tail end cut angle 20° *8
    NZE141G
    ZRE142G
    1NZ-FE
    2ZR-FE
    06.10- MS153-12008 E Discontinued

    Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    TRD logo attached on baffle
    ※Suitable to models with OE optional rear Under Spoiler.

    MS153-12004
    (17400-ZE400)
    E Discontinued
    COROLLA Axio NZE141
    ZRE142
    1NZ-FE
    2ZR-FE
    06.10- MS153-12008 E Discontinued

    Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    TRD logo attached on baffle

    MS153-12004
    (17400-ZE400)
    E Discontinued
    COROLLA RUMION 1.8L / Vehicle without rear bumper spoiler 2ZR-FE 07.10- MS153-12009 E Discontinued Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    MS153-12002 E Discontinued
    1.5L / Vehicle without rear bumper spoiler 1NZ-FE MS153-12010 E Discontinued Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    MS153-12003 E Discontinued
    1.8L / Vehicle without rear bumper spoiler 2ZR-FE MS153-12011 E Discontinued Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    *For vehicle of Aero tourer grade and with Toyota genuine rear bumper spoiler.
    MS153-12006
    E Discontinued
    1.5L / Vehicle without rear bumper spoiler 1NZ-FE MS153-12012
    E Discontinued Oval shape single tail(H95mm×H70mm)
    Tail end cut angle 20°(Cut-end curling finish)
    *For vehicle of Aero tourer grade and with Toyota genuine rear bumper spoiler.
    MS153-12007 E Discontinued
    COROLLA RUNX,
    ALLEX
    ZZE123 2ZZ-GE 01.1-04.4 17400-ZE220 C Discontinued Pipe dia. φ60.5、φ78 Single tail *2 *9
    04.4- 17400-ZE240 C Discontinued Pipe dia. φ60 Oval shape single tail(W100×H60)
    TRD logo attached on baffle
    Tail end cut angle 20° *9
    COROLLA(Sedan),
    SPRINTER(Sedan)
    AE111 4A-GE 97.4-00.8 17400-AE031 W Discontinued Pipe dia. φ60.5、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut
    AE110 5A-FE 95.5-00.8 17400-AE130 C Discontinued Pipe dia. φ48.6、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut It's required to cut exhaust pipe.
    AE114 4A-FE 95.5-00.8 17400-AE120 W Discontinued Pipe dia. φ54.0、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut
    LEVIN, TRUENO AE111 4A-GE 95.5-00.8 17400-AE100 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    AE111 4A-FE 95.5-00.8 17400-AE110 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    AE110 5A-FE 95.5-00.8 17400-AE130 C Discontinued Pipe dia. φ48.6、φ76.3 Single tail,
    Tail end cut angle 15°Slanting cut It's required to cut exhaust pipe.
    CERES, MARINO
    (95.5-)
    AE101 4A-GE 95.5-98.8 17400-AE100 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    AE101 4A-FE 95.5-98.8 17400-AE110 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    AE100 5A-FE 95.5-98.8 17400-AE130 C Discontinued Pipe dia. φ48.6、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut It's required to cut exhaust pipe.
    COROLLA WAGON AE101G 4A-GE -00.8 17400-AE031 W Discontinued Pipe dia. φ60.5、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut
    AE100G 5A-FE 95.5-00.8 17400-AE130 C Discontinued Pipe dia. φ48.6、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut It's required to cut exhaust pipe. *10
    CORONA EXiV、
    CARINA ED(Except 4WS model)
    ST202 3S-GE 93.10-98.4 17400-ST020 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    ST202 3S-FE 93.10-98.4 17400-ST030 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    CORONA(PREMIO) AT21# 4A-FE
    7A-FE
    96.1-01.12 17400-ST100 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    ST210 3S-FE 96.1-01.12 17400-ST100 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    CROWN ATHLETE
    CROWN ROYAL
    GRS18#

    3GR-FSE
    4GR-FSE

    03.12- 17400-GS800 C 190, 000 Pipe dia. φ60.5
    Oval shape single tail(H82mm×W112mm) comes on RH&LH
    TRD logo attached on baffle
    Tail end cut angle 15°
    CROWN MAJESTA UZS18#

    3UZ-FE

    04.7- 17400-US801 C Discontinued Pipe dia. φ60.5
    Oval shape single tail(H82mm×W112mm) comes on RH&LH
    TRD logo attached on baffle
    Tail end cut angle 12°
    ESTIMA ACR30・40W
    MCR30・40W
    1MZ-FE, 2AZ-FE 99.12- 17400-MR300 W Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut *1
    GSR50W 2GR-FE 06.1- Muffler section MS153-28001
    (17430-GR500)
    C Discontinued Must use with below tail section *11
    Tail section MS153-28005
    (17431-GR500)
    C Discontinued
    Must use with above muffler section *11 G, X(Except model with OE optional rear Under Spoiler) *10 Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    MS153-28006
    (17431-GR510)
    Discontinued G, X(Applicable to model with OE optional rear Under Spoiler),Aeras
    GSR55W 2GR-FE 06.1- Muffler section MS153-28002
    (17430-GR510)
    C Discontinued Must use with below tail section *11
    Tail section MS153-28005
    (17431-GR500)
    C Discontinued Must use with above muffler section *11 G, X(Except model with OE optional rear Under Spoiler) *10 Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    MS153-28006
    (17431-GR510)
    Discontinued G, X(Applicable to model with OE optional rear Under Spoiler),Aeras
    ACR50W 2AZ-FE 06.1- Muffler section MS153-28003
    (17430-AR500)
    C Discontinued Must use with below tail section *11
    Tail section MS153-28005
    (17431-GR500)
    C Discontinued Must use with above muffler section *11 G, X(Except model with OE optional rear Under Spoiler) *10 Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    MS153-28006
    (17431-GR510)
    Discontinued G, X(Applicable to model with OE optional rear Under Spoiler),Aeras
    ACR55W 2AZ-FE 06.1- Muffler section MS153-28004
    (17430-AR510)
    C Discontinued Must use with below tail section *11
    Tail section MS153-28005
    (17431-GR500)
    C Discontinued Must use with above muffler section *11 G, X(Except model with OE optional rear Under Spoiler) *10 Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    MS153-28006
    (17431-GR510)
    Discontinued G, X(Applicable to model with OE optional rear Under Spoiler),Aeras
    GSR50W G,X grade without Rear bumper spoiler 2GR-FE 06.1- Muffler & Tail set MS153-28012 E Discontinued Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    GSR50W G,X grade with Rear bumper spoiler,Aeras MS153-28013 E Discontinued Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    GSR55W G,X grade without Rear bumper spoiler 2GR-FE MS153-28014 E Discontinued Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    GSR55W G,X grade with Rear bumper spoiler,Aeras MS153-28015 E Discontinued Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    ACR50W G,X grade without Rear bumper spoiler 2AZ-FE MS153-28016 E Discontinued Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    ACR50W G,X grade with Rear bumper spoiler,Aeras MS153-28017 E 87, 000 Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    ACR55W G,X grade without Rear bumper spoiler 2AZ-FE MS153-28018 E Discontinued Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    ACR55W G,X grade with Rear bumper spoiler,Aeras MS153-28019 E 62, 000 Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    ESTIMA HYBRID
    AHR10W 2AZ-FXE 01.5- 17400-MR300 W Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut *1
    AHR20W 2AZ-FXE 06.6- Muffler section MS153-28004
    (17430-AR510)
    C Discontinued Must use with below tail section *11
    Tail section MS153-28005
    (17431-GR500)
    C Discontinued Must use with above muffler section *11 Except model with OE optional rear Under Spoiler Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    MS153-28006
    (17431-GR510)
    C Discontinued Must use with above muffler section *11 Applicable to model with OE optional rear Under Spoiler Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    2AZ-FXE 09.1- Muffler & Tail set MS153-28019 E 62, 000 Oval shape single tail(H82mm×W112mm)
    TRD logo attached on baffle
    Tail end cut angle 12°Slanting cut
    HARRIER ACU3#W, MCU3#W 1MZ-FE, 2AZ-FE 03.02-10.03 MS153-48001
    (17400-MU300)
    C Discontinued Pipe dia. φ65.0 φ100 Single tail Cut-end curling finish
    TRD logo attached on baffle
    Tail end cut angle 15° *1
    HARRIER HYBRID MHU38W 3MZ-FE 05.3- MS153-48001
    (17400-MU300)
    C Discontinued Pipe dia. φ65.0 φ100 Single tail Cut-end curling finish
    TRD logo attached on baffle
    Tail end cut angle 15°
    HILUX SURF VZN185 5VZ-FE 95.11-02.11 17400-ZN800 W Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut *12 *1
    VZN180 5VZ-FE 98.8-02.11
    KZN185 1KZ-TE -98.8 17400-KN800 W Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut *13 *1
    RZN・TRN・VZN・KDN21#W, GRN215W 5VZ-FE,
    3RZ-FE, 2TR-FE, 1KD-FTV
    02.10- MS153-60002 E Discontinued Pipe dia. φ60.5、φ100 Single tail, TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1
    MS153-60001
    (17400-RN101)
    C Discontinued Pipe dia. φ60.5、φ100 Single tail, TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1
    IPSUM SXM10G 3S-FE 96.5-01.4 17400-SM100 C Discontinued Pipe dia. φ54、φ80 Single tail
    Tail end cut angle 15°Slanting cut
    ACM21W 2AZ-FE 01.5-03.10 Muffler section 17430-AR600 W Discontinued Must use with below tail section *14 Pipe dia. φ50.8 *1
    Tail section 17431-AM210 W Discontinued Must use with above muffler section *14 240S, 240i Type-S,
    240i Type-G,
    Applicable to model with OE optional rear Under Spoiler
    only
    Pipe dia. φ50.8、
    φ76.3 Single tail
    TRD logo attached on baffle
    Tail end cut angle 30°Slanting cut

    03.10-

    Muffler section 17430-AR600 W Discontinued Must use with below tail section *14 Pipe dia. φ50.8 *1
    Tail section 17431-AM220 W Discontinued Must use with above muffler section *14 Applicable to 240S only Pipe dia. φ60.8、
    Oval shape single tail(H60mm×W100mm)
    Cut-end curling finish
    TRD logo attached on baffle
    Tail end cut angle 20°Slanting cut
    ist NCP60・61
    (Except A, A-S grade)
    2NZ-FE
    1NZ-FE
    02.5- 17400-NP600 C Discontinued Pipe dia. φ48.6、Oval shape single tail(H62mm×W90mm)
    Tail end cut angle 15°Slanting cut *2
    NCP60・61
    (A, A-S grade)
    2NZ-FE
    1NZ-FE
    05.5- 17400-NP610 C Discontinued φ89.1 Single tail
    Cut-end curling finish. TRD logo attached on baffle
    KLUGER L・V ACU2#W, MCU2#W 1MZ-FE, 2AZ-FE 03.8- MS153-48001
    (17400-MU300)
    C Discontinued Pipe dia. φ65.0 φ100 Single tail Cut-end curling finish
    TRD logo attached on baffle
    Tail end cut angle 15° *8 *1
    KLUGER HYBRID MHU28W 3MZ-FE 05.3- MS153-48001
    (17400-MU300)
    C Discontinued Pipe dia. φ65.0 φ100 Single tail Cut-end curling finish
    TRD logo attached on baffle
    Tail end cut angle 15°
    LAND CRUISER PRADO GRJ150W・151W, TRJ150W 1GR-FE, 2TR-FE 09.9- MS153-60002 E Discontinued Pipe dia. φ60.5, φ100S Single Tail
    TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1 *19
    GRJ150W・151W, TRJ150W 1GR-FE, 2TR-FE 09.9-10.3 MS153-60001 C Discontinued Pipe dia. φ60.5, φ100S Single Tail
    TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1 *19
    VZJ95(5 door model exclusive) 5VZ-FE   17400-ZN800 W Discontinued Pipe dia. φ60.5、φ80 Single tail
    Tail end cut angle 15°Slanting cut *1
    KZJ95(5 door model exclusive) 1KZ-TE -99.6 17400-KN800 W Discontinued Pipe dia. φ60.5、φ80 Single tail
    Tail end cut angle 15°Slanting cut *1
    RZJ120W, TRJ120W
    VZJ120・121W
    KDJ120・121W(5 door model exclusive)
    5VZ-FE, 3RZ-FE, 2TR-FE, 1KD-FTV 02.10-09.8 MS153-60002 E Discontinued 5 door model exclusive Pipe dia. φ60.5、φ100 Single tail,
    TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1
    MS153-60001
    (17400-RN101)
    C Discontinued 5 door model exclusive Pipe dia. φ60.5、φ100 Single tail,
    TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1
    LAND CRUISER10# HDJ101K 1HD-FTE   17400-HJ000 W Discontinued Pipe dia. φ65、φ76.3 Dual tail
    Tail end cut angle 15°Slanting cut *15 *1
    MARK X GRX120・121・125 3GR-FSE
    4GR-FSE
    04.11- MS153-22001
    (17400-GX200)
    C Discontinued comes on RH&LH ※This is an exchange type to this side of a genuine muffler baffle.
    MR2 SW20 3S-GTE 89.10-99.10 17400-SW240 C Discontinued Pipe dia. φ60.5、φ100 Single tail comes on RH&LH
    Tail end cut angle 15°Slanting cut
    SW20 3S-GE 89.10-99.10 17400-SW230 C Discontinued Pipe dia. φ54.0、φ100 Single tail comes on RH
    Tail end cut angle 15°Slanting cut
    MR-S ZZW30 1ZZ-FE 99.10- 17400-ZW300 C Discontinued Pipe dia. φ60.5、φ100 Single tail
    Tail end cut angle 15°Slanting cut
    NOAH
    VOXY
    2WD
    ZRR70G
    ZRR70W
    3ZR-FE
    3ZR-FAE
    '07.6 - '10.3 MS153-28007 E Discontinued Muffler section, 2WD All Model
    Must use with below tail section
    MS153-28009 E Discontinued Tail section, with Genuine Spoiler
    Tail end: Single (W 100 mm x H 60 mm)
    MS153-28010 E Discontinued Tail section, without Genuine Spoiler
    Tail end: Single (W 112 mm x H 82 mm)
    ZRR70G
    ZRR70W
    3ZR-FE
    3ZR-FAE
    '07.6 - '10.4 MS153-28020 E Discontinued Muffler and Tail set, with Genuine Spoiler
    Tail end: Single (W 100 mm x H 60 mm)
    MS153-28021 E Discontinued Muffler and Tail set, without Genuine Spoiler
    Tail end: Single (W 112 mm x H 82 mm)
    3ZR-FAE '10.4 - MS153-28021 E Discontinued Muffler and Tail set, All Model
    Tail end: Single (W 112 mm x H 82 mm)
    * Can not install to G's model
    NOAH
    VOXY
    4WD
    ZRR75G
    ZRR75W
    3ZR-FE
    3ZR-FAE
    '07.6 - '10.3 MS153-28008 E Discontinued Muffler and Tail set, with Genuine Spoiler
    Tail end: Single (W 100 mm x H 60 mm)
    MS153-28011 E Discontinued Muffler and Tail set, without Genuine Spoiler
    Tail end: Single (W 112 mm x H 82 mm)
    ZRR75G
    ZRR75W
    3ZR-FE
    3ZR-FAE
    '07.6 - '10.4 MS153-28022 E Discontinued Muffler and Tail set, with Genuine Spoiler
    Tail end: Single (W 100 mm x H 60 mm)
    MS153-28023 E Discontinued Muffler and Tail set, without Genuine Spoiler
    Tail end: Single (W 112 mm x H 82 mm)
    3ZR-FAE '10.4 - MS153-28023 E Discontinued Muffler and Tail set, All Model
    Tail end: Single (W 112 mm x H 82 mm)
    PASSO KGC10 1KR-FE 04.6- MS153-B1002
    (17400-KC100)
    C Discontinued Pipe dia. φ42.7、Oval shape single tail(H60mm×W100mm)
    Cut-end curling finish TRD logo attached on baffle Tail end cut angle 20°
    QNC10(Except Racy grade) K3-VE MS153-B1001
    (17400-QC100)
    C 64, 000 Pipe dia. φ42.7、Oval shape single tail(H60mm×W100mm)
    Cut-end curling finish TRD logo attached on baffle Tail end cut angle 20°
    QNC11(Racy grade exclusive) K3-VE 04.12- MS153-B1003
    (17400-QC110)
    C Discontinued Pipe dia. φ42.7, φ89.1 Single tail
    Cut-end curling finish TRD logo attached on baffle
    PRIUS
    PRIUS PHV
    ZVW30・35 2ZR-FXE 09.05 - MS153-47001 E Discontinued Oval shape single tail(H70mm×W95mm)
    Cut-end curling finish TRD logo attached on baffle Tail end cut angle
    * Recommend installation with TRD Rear Bumper Spoiler.
    PRIUS α ZVW4# 2ZR-FXE 11.5 - MS153-47002 E 56, 000 φ70mm Dual tail
    Cut-end curling finish TRD logo attached
    on baffle Tail end cut angle
    RAV4 SXA1#G・W 3S-FE, 3S-GE
    (Except 3S-GE model after '98.8)
    94.5-00.5 17400-SA100 W Discontinued Pipe dia. φ54、φ70 Single tail,
    Can't install with OE optional rear step bar at the same time. *16
    SPRINTER CARIB AE111G 4A-GE   17400-AE031 W Discontinued Pipe dia. φ60.5、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut
    AE114G・115G 4A-FE, 7A-FE   17400-AE120 W Discontinued Pipe dia. φ54.0、φ76.3 Single tail
    Tail end cut angle 15°Slanting cut *17
    STARLET
    (Turbo model only)
    EP91 4E-FTE 96.1-99.7 17400-EP900 C Discontinued Pipe dia. φ54.0、φ100 Single tail(Tail pipe only)
    Tail end cut angle 15°Slanting cut
    SUPRA JZA80 2JZ-GE
    2JZ-GTE
    93.5-02.8 17400-JA810 C Discontinued Pipe dia. φ80、φ115 Single tail
    Tail end cut angle 15°Slanting cut *2
    SOARER UZZ40 3UZ-FE 01.4- 17400-UZ400 C Discontinued Pipe dia. φ54、φ110 Single tail(Cut-end curling finish) comes on RH&LH
    Tail end cut angle 15°
    VELLFIRE 240V/X
    Excluding Hybrid or
    Side Lift Up Seat Model
    2AZ-FE 08,05 - MS153-58003 E Discontinued φ75 Single tail
    240Z
    Excluding Hybrid or
    Side Lift Up Seat Model
    2AZ-FE MS153-58004 E 66, 000 φ100 Single tail
    350V/X
    Excluding Hybrid or
    Side Lift Up Seat Model
    2GR-FE MS153-58005 E 66, 000 φ75 Single tail
    350Z
    Excluding Hybrid or
    Side Lift Up Seat Model
    2GR-FE MS153-58006 E 66, 000 φ100 Single tail
    WISH
    (1.8L 2WD)
    ZNE10G 1ZZ-FE 03.1- MS153-68002
    (17400-ZE100)
    C Discontinued Pipe dia. φ48.6 φ100 Single tail TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1 *18
    * Applicable to model w/o OE optional rear Under Spoiler and Aero Sports Package only
    WISH
    (2.0G)
    ANE10G 1AZ-FSE 03.5-
    WISH
    (1.8L 2WD)
    ZNE10G 1ZZ-FE 05.9- MS153-68003
    (17400-ZE110)
    C Discontinued Oval shape single tail(W100mm×H60mm) Cut-end curling finish
    TRD logo attached on baffle Tail end cut angle 20°
    WISH
    (2.0G)
    ANE10G 1AZ-FSE 05.9-
    WISH
    (2.0Z)
    ANE11W 1AZ-FSE 03.5- MS153-68001
    (17400-AE150)
    C Discontinued Pipe dia. φ48.6 φ100 Single tail TRD logo attached on baffle
    Tail end cut angle 15°Slanting cut *1
    Vitz SCP10・13 1SZ-FE, 2SZ-FE 99.1-05.2 17400-NP100 C Discontinued Pipe dia. φ38.1 Oval shape single tail(H62mm×W90mm)
    Tail end cut angle 15°Slanting cut *2
    NCP10・13 1NZ-FE, 2NZ-FE 00.10-05.2 17400-NP110 C Discontinued Pipe dia. φ48.6 φ89.1 Single tail
    Tail end cut angle 15°Slanting cut *2
    NCP91(RS exclusive) 1NZ-FE 05.2- MS153-52001
    (17400-NP900)
    C Discontinued Oval shape single tail(W100mm×H60mm) Cut-end curling finish
    TRD logo attached on baffle Tail end cut angle 20°
    MS153-52008 E Discontinued Oval shape single tail(W100mm×H60mm) Cut-end curling finish
    TRD logo attached on baffle Tail end cut angle 20°
    KSP90 1KR-FE 17400-KP900 C 59, 000 Oval shape single tail(W100mm×H60mm) Cut-end curling finish
    TRD logo attached on baffle Tail end cut angle 20°
    note:Discolouration may occur to surface of heat-resistant black metallic paint, foundation finish and polish finish according to the condition the muffler is being used.
    *1 Muffler section is stainless finish.(On rearer muffler section for HILUX SURF & LAND CRUISER)
    *2:Muffler section is stainless finish.
    *3:Tali position moved to rear side.Approx. +35mm
    *4 Can not install individually. Must install with TRD Rear Bumper Spoiler(MS343-1200#).
    *5:Not applicable to vehicle after '97.12
    *6:Tali position moved to rear side. M/T model: approx. +45mm, A/T model: approx. +50mm
    *7:Tali position moved to rear side. M/T model: approx. +30mm, A/T model: approx. +40mm
    *8 Can't install with OE optional Rear Under Spoiler at the same time.
    *9:Can't install with OE optional rear bumper spoiler at the same time.
    *10 Bottom position becomes 11mm lower than original muffler.
    *11 Can't install individually. Install both center pipe and tail pipe. Must choose tail pipe based on your vehicle grade.
    *12 Tail position moved 38mm to left side when installing on VNZ185(95.12-98.8).
    *13 Tali position moved to LH side approx. +38mm.
    *14 Can't install muffler section and tail section separately. Tail section designed to fit with rear bumper shape. Please refer application on right in the chart.
    *15 Suitable to model with under pull-up spare tyre. However, it's impossible to install with dealer optional rear under step at the same time.
    *16 For vehicle after '97.9, it's require to replace with Toyota genuine parts follows. (Replacement non necessary to 3S-GE model after '98.8).
    ●Support BracketRH(17509-74180)×1●Support rubber(17565-74420)×2●Support BracketLH(17508-74110)×1●Attachment bolt(90119-08701)×1
    *17 Bottom position becomes 14mm lower than original muffler.
    *18 Can't install with OE optional rear bumper spoiler(05.9-) at the same time.
    *19 Able to install with genuine rear skid plate.



    WayDo Dress-up Muffler
    Vehicle Model Code Year Model Part No. Code List Price(JPY) Remarks
    FunCargo NCP20・21   17400-NP300 W 38, 000 For NCP20・21、φ100 Single tail、All stainless
    Tail end cut angle 15°Slanting cut
    bB NCP30・31 -03.4 17400-NP300 W 38, 000

    For NCP30・31、φ100 Single tail、All stainless
    Tail end cut angle 15°Slanting cut

    *Discolouration may occur to surface of heat-resistant black metallic paint, foundation finish and polish finish according to the condition the muffler is being used.